Error code list for Junker dishwasher

E01
Cause:
Electronics error or water in the base.
Solution:
Replace the level sensor.
Level switch
E02
Cause:
Electronics error.
Solution:
An electronics error can be due to a faulty control module, but can also be due to defects in other electronics. To find out more about the problem, we recommend that you search for symptoms via our troubleshooting guide instead.
E03
Cause:
Electronics error.
Solution:
An electronics error can be due to a faulty control module, but can also be due to defects in other electronics. To find out more about the problem, we recommend that you search for symptoms via our troubleshooting guide instead.
E04
Cause:
Electronics error.
Solution:
An electronics error can be due to a faulty control module, but can also be due to defects in other electronics. To find out more about the problem, we recommend that you search for symptoms via our troubleshooting guide instead.
E05
Cause:
Electronics error.
Solution:
An electronics error can be due to a faulty control module, but can also be due to defects in other electronics. To find out more about the problem, we recommend that you search for symptoms via our troubleshooting guide instead.
E06
Cause:
Door sensor error.
Solution:
Replace the door lock.
E07
Cause:
Drying system error.
Solution:
Replace the Zeolith container.
E08
Cause:
Water level too low by heating element.
Solution:
Replace the aquastop.
Aquastop
E09
Cause:
Heat system error.
Solution:
Replace the heat pump.
E10
Cause:
Drying system error.
Solution:
Replace the Zeolith container.
E11
Cause:
Thermostat or temperature sensor error.
Solution:
Replace the thermostat.
E12
Cause:
Limescale formation at the heater.
Solution:
Descale the dishwasher and check if the salt level is set correctly.
E13
Cause:
The water temperature exceeds 75 degrees.
Solution:
The error usually indicates that the supply hose is connected to the hot water tap. Connect the hose to the cold water tap instead.
E14
Cause:
Error in filling system or error in water supply registered.
Solution:
Replace the flow sensor.
E15
Cause:
Water in dishwasher base.
Solution:
The error code usually occurs due to a leak. To find the spare part that causes the error, you can follow the limescale trace. Replace the faulty spare part.
E16
Cause:
Error in filling system or error in water supply registered.
Solution:
Replace the aquastop.
Aquastop
E17
Cause:
Error in filling system or error in water supply registered.
Solution:
The error code usually occurs due to a leak. To find the spare part that causes the error, you can follow the limescale trace. Replace the faulty spare part.
E18
Cause:
Error in filling system or error in water supply registered.
Solution:
Replace the drain pump.
Drain pump
E19
Cause:
Dispenser error.
Solution:
A dispenser error can be due to a defective dispenser, but can also be due to defects in other parts. To find out more about the problem, we recommend that you search for symptoms via our troubleshooting guide instead.
E20
Cause:
Wash motor error.
Solution:
Replace the wash motor.
Circulation pump
E21
Cause:
Wash motor error.
Solution:
Replace the wash motor.
Circulation pump
E22
Cause:
Clogged bottom sieve and/or filter.
Solution:
Replace the drain pump.
Drain pump
E23
Cause:
Drain pump error.
Solution:
Replace the drain pump.
Drain pump
E24
Cause:
Water level error.
Solution:
Replace the drain pump.
Drain pump
E25
Cause:
Drain pump error.
Solution:
Replace the drain pump.
Drain pump
E26
Cause:
Water supply switch error.
Solution:
Replace the aquastop.
Aquastop
E27
Cause:
Mains or supply voltage too low during washing (less than 170 V).
Solution:
Check the power cord and voltage.
E28
Cause:
Flow sensor error.
Solution:
Replace the flow sensor.
E29
Cause:
Water in dishwasher base.
Solution:
The error code usually occurs due to a leak. To find the spare part that causes the error, you can follow the limescale trace. Replace the faulty spare part.
E31
Cause:
Drying system error.
Solution:
Replace the Zeolith container.
E92-40
Cause:
Cannot drain water.
Solution:
Clean the filter. If the error code still appears after this, it is possible that it is caused by a faulty drain pump.
Drain pump
H06
Cause:
Delayed start activated.
Solution:
The error code indicates that delay start is enabled. Press Delay start (see the user manual if you are unsure where to find this) and hold it until it shows 00 and the dishwasher should now be working again. However, be aware that H06 can also be displayed when, e.g., setting the signal volume and setting the rinse aid. If you are in doubt, you should check the dishwasher's user manual.

Professional dishwasher gel (500 ml)
This professional dishwasher gel is a sublime alternative to traditional dishwashing detergents, which difficultly dissolves completely, resulting in soap residue on the dishes. Especially with newer dishwashers, which are hugely water-saving, you may experience soap residue. You will avoid that with this smart dishwasher gel – the gel is so easily soluble that soap residue on dishes is a thing of the past! The dishwasher gel is also easy to dose - simply press lightly on the bottle and let approx. 20 ml out per wash. Many dishwashers have a measuring unit on the soap container, but if yours doesn't, it roughly corresponds to a large tablespoon.

In addition, always ensure that there is salt and rinse aid in the dishwasher. Salt, rinse aid and soap, in interaction with each other, ensure the most optimal dishwashing result.
4.95GBP
In stock. Del 2-3 work days.
Read more.
Professional machine cleaner for dishwashers (500 ml)
Our professional machine cleaner for dishwashers is a specially developed product that helps remove limescale, grease and food residues from your machine. With regular use, you ensure that the dishwasher works optimally and lasts longer. The product helps achieve better washing results.

Why use Professional Machine Cleaner?
Dish soap and similar detergents (e.g. gel or powder) ensure that your tableware is clean - but only as long as the dishwasher is clean. The more dirt, limescale and grease that settles inside the dishwasher, the more your washing results are affected. Perhaps you have experienced that your tableware smells, even though it has just been finished in the dishwasher - or that there is still dirt and food residue on it after you have finished washing. Your dishwasher needs to be cleaned in the same way as your crockery. Professional machine cleaning is designed to penetrate deep into machine parts and effectively remove these deposits.
17.95GBP
In stock. Del 2-3 work days.
Read more.

Cookie information

Error code list for Junker dishwasher

E01

Cause:

Solution:

E02

Cause:

Solution:

E03

Cause:

Solution:

E04

Cause:

Solution:

E05

Cause:

Solution:

E06

Cause:

Solution:

E07

Cause:

Solution:

E08

Cause:

Solution:

E09

Cause:

Solution:

E10

Cause:

Solution:

E11

Cause:

Solution:

E12

Cause:

Solution:

E13

Cause:

Solution:

E14

Cause:

Solution:

E15

Cause:

Solution:

E16

Cause:

Solution:

E17

Cause:

Solution:

E18

Cause:

Solution:

E19

Cause:

Solution:

E20

Cause:

Solution:

E21

Cause:

Solution:

E22

Cause:

Solution:

E23

Cause:

Solution:

E24

Cause:

Solution:

E25

Cause:

Solution:

E26

Cause:

Solution: